BlackEtch DIY SWAGELESS Wire Balustrade - Timber Insert System - Suits Timber Posts

Wire Balustrade - Timber Insert - Black

Is one of our most streamline swageless systems. It is suitable for use with timber posts and is great for both straight sections and stair sections (with angle connectors). Tension is created on the wire by threading the LHT/ RHT swageless studs into the LHT/ RHT timber inserts. Tightening the nuts against the head of the timber inserts locks the system in place.

Note: This system is supplied as components only. Assembly is done on-site by the installer.

THIS SYSTEM:
• Is suitable for use with timber posts
• Is great for both flat and stair sections (with angle connectors)

KEY BENEFITS TO THIS SYSTEM:
• Extremely quick and simple installation 
• BlackEtch process offers a unique, stylish, and durable finish
• BlackEtch process offers a smooth black finish with superior corrosion resistance
• All fittings made from high quality 316 grade stainless steel (Timber inserts 304 grade)
• This system is suitable for both flat and stair sections when used with angle connectors on stairs.

COMPONENTS REQUIRED PER WIRE:
Individual items can be added to the cart from below:
1 x BS-3310-06L -M6 x 32 LHT Threaded Timber Insert 304 Grade
1 x BS-3310-06R - M6 x 32 RHT Threaded Timber Insert 304 Grade
1 x BSL-7801-03635L - M6 x 35mm LHT Swage Stud to suit 3.2mm Wire 316 Grade
1 x BSL-7801-03635R - M6 x 35mm RHT Swage Stud to suit 3.2mm Wire 316 Grade
2 x S03 - Cut and Factory Swage (Additional Cost)
BWRS119316-032 - 3.2mm 1 x 19 Wire Rope 316 Grade (Additonal cost Charged per Metre)

Add Ons for Stairs:
1 x BS-7813L-0615 - Swivel Connector M6 x 15mm LHT - 316 Grade Stainless Steel
1 x BS-7813R-0615 - Swivel Connector M6 x 15mm RHT - 316 Grade Stainless Steel



Exclusively available through AWR Solutions our BlackEtch process offers a unique, stylish, and durable finish to your wire balustrade system. Etched into the surface of the fittings and wire our BlackEtch process offers a smooth black finish with superior corrosion resistance. To see this great finish for yourself we recommend ordering a free sample here.

AWR Solutions only recommends the use our own internal factory swaging system when purchasing the BlackEtch range of hardware and wire rope. Alternative Swaging procedures will not be covered under AWR Solutions standard product warranty.

 

Wire Balustrade FAQ'S for this system


Q:  What hole size do I need in my posts for the Timber Insert System?

 

A: You will require an 7.5mm hole to a depth of 35mm in your end connection posts to install the Timber Inserts. For your intermediate posts, an 8mm hole will be required to pass the threaded terminal through.

 

Note: if you are using split grommets (106874FB or 106874FS) you will require an 11/32” hole (8.73mm ) in your intermediate posts.

 

 

Q:  Can I use this system for Stairs?

 

A: Yes the Timber Insert System is suited to both straight Sections and stair sections (when used with angle connectors)

 

Q:  What is the maximum length I can use with the Timber Insert System?

 

A: The maximum recommended span between connection posts for this system is 10 metres.

 

Q:  What size and type of wire should I use for this system?

 

A: Our DIY Swageless systems are specifically designed to be used with 3.2mm 1 x 19 wire rope.

 

Q: Do I need any special tools to install this Wire Balustrade System?

 

A: You will require a power drill, 7.5mm drill, 8mm drill bit, 1/4" Hex Drive Bit. We also recommend purchasing  2 x Multi Tools to tension the system and lock in place.

 

Q:  Can I run my Wire Balustrade around corners?

 

A: We strongly advise against bending your wire around corners and angled sections. This can fatigue the wire over time as well as damage to your posts (especially timber). Wires should be terminated at each corner and end post.

 

Q:  How many runs of wire do I need for my balustrade?

 

A: To comply with Australian NCC regulations most wire balustrades will require 80mm spacing between your wires when your intermediate posts are no more than 1500mm apart. We highly recommend reading the Wire Balustrade Regulations Help section of our website prior to ordering.

 


More Questions? No problem, just send us an email at sales@awrsolutions.com.au or give us a call on 1300 781 266 and we would be happy to help.

(WBSLB-TIS)

Be The First To Review This Product!

Help other AWR Solutions users shop smarter by writing reviews for products you have purchased.

Write a product review

We Also Recommend

You May Also Like

More From This Category