Bright Finish DIY SWAGELESS Wire Balustrade - Metal Insert System - Suits Metal Posts

Wire Balustrade - Metal Insert System - DIY SWAGELESS

Is one of our most streamline swageless systems. It is suitable for use with metal posts and is great for both straight sections and stair sections (with angle connectors). Tension is created on the wire by threading the LHT/ RHT swageless studs into the LHT/ RHT Nutserts. Tightening the nuts against the head of the Nutserts locks the system in place.

Note: This system is supplied as components only. Assembly is done on-site by the installer.

THIS SYSTEM:
• is suitable for use with metal posts
• is great for both flat and stair sections (when used with angle connectors)

KEY BENEFITS OF THIS SYSTEM:
• Extremely quick and simple installation 
• Uses ultra-bright and sleek 1 x 19 wire rope
• All fittings made from high quality 316 grade stainless steel (Nutserts 304 grade)
• This system is suitable for both flat and stair sections when used with angle connectors on stairs.

COMPONENTS REQUIRED PER WIRE:
1 x NS-SS-M06-L - M6 LHT Large Flange Nutsert 304 Grade
1 x NS-SS-M06-R - M6 RHT Large Flange Nutsert 304 Grade
1 x SL-7801-03635L - M6 x 35mm LHT Swage Stud to suit 3.2mm Wire 316 Grade
1 x SL-7801-03635R - M6 x 35mm RHT Swage Stud to suit 3.2mm Wire 316 Grade
WRS119316-032-MTR - 3.2mm 1 x 19 Wire Rope 316 Grade (Sold Separately - per Metre)

Add Ons for Stairs:
1 x SS-7813R-0615 - Swivel Connector M6 x 15mm LHT - 316 Grade Stainless Steel
1 x SS-7813L-0615 - Swivel Connector M6 x 15mm RHT - 316 Grade Stainless Steel

HOW IT WORKS
Our DIY swageless fittings are extermely easy to use. Simply cut the wire and push into the fitting. The spring jaw mechanism inside the fitting grips the wire for an extremely secure and tight hold with no swaging tools required. Designed for use on 3.2mm 1 x 19 wire rope only.

Wire Balustrade FAQ'S for this system

 

Q: What are the best Wire Balustrade posts for the Wire Balustrade - Metal Insert System?

 

A: Wire Balustrade - Metal Insert System is suitable for use with metal posts

 

Q: Is this product suitable for a Flat Wire Balustrade or Stair Wire Balustrade?

 

A: Wire Balustrade - Metal Insert System is suited to both straight Sections and stair sections (when used with angle connectors)

 

Q: How long does it take for my wires to be manufactured?

 

A: This system is suplied as componnets only to be assembled and installed on-site. Order before 2pm for same day dispatch..

 

Q: What hole size do I need in my posts for the Wire Balustrade - Metal Insert System?

 

A: You will require an 9mm hole in your end connection posts to install the Nut Rivets. For your intermediate posts, an 4mm hole will be required to pass the 3.2mm wire rope through. Note: if you are using split grommets (106874FB or 106874FS) you will require an 11/32” hole (8.73mm ) in your intermediate posts. Note: A Nut Rivet Tool is required to install the Nut rivets in your end posts.

 

Q: Can I use this Wire Balustrade System for Stairs?

 

A: Yes the Metal Insert System can be used on stairs but you will require 1 x LHT Angle Connector and 1 x RHT Angle Connector per wire.

 

Q: What is the maximum length I can use with the Wire Balustrade Metal Insert System?

 

A: The maximum recommended span between connection posts for this system is 10 metres.

 

Q: Do I need any special tools to install this Wire Balustrade system?

 

A: You will need a power drill and Drill Bits (If posts not being supplied). This system does also require Nut Rivet Tool capable of installing LHT Nut Rivets. We also recommend purchasing  2 x Multi Tools to tension the system and lock in place.

 

Q: Can I run my around corners?

 

A: We strongly advise against bending your wire around corners and angled sections. This can fatigue the wire over time as well as damage to your posts (especially timber). Wires should be terminated at each corner and end post.

 

Q: How many runs of wire do I need for my Balustrade?

 

A: To comply with Australian NCC regulations most wire balustrades will require 80mm spacing between your wires when your intermediate posts are no more than 1500mm apart. We highly recommend reading the Wire Balustrade Regulations Help section of our website prior to ordering.

 


More Questions? No problem, just send us an email at sales@awrsolutions.com.au or give us a call on 1300 781 266 and we would be happy to help.

(WBSL-MIS)

Be The First To Review This Product!

Help other AWR Solutions users shop smarter by writing reviews for products you have purchased.

Write a product review

We Also Recommend

You May Also Like

More From This Category